Fence Building The basic theory is that you stake out where your fence will be and stretch a string between them. This will be a guideline when you are installing the posts. If your fence starts with your house you will probably like to have it at a right angle. It is a simple procedure to get this right. First stake the spot where you like your fence to start. do it yourself deck design ideas and how to build a wood deck plans. Fasten a string to the stake and stretch it out roughly perpendicular to your house. Measure out 1,5-meter out on the string and mark it. Mark a point on your house one-meter from the stake. Hold a tape measure diagonally between the one-meter mark and the 1,5-meter mark and move the string until the distance between the marks is 2-meter.

How to Build a Privacy Fence

A fence can be useful for several things like privacy, weather barrier, and containment for children or just for decoration. Your imagination is the only thing that’s limit the design. You can get some good ideas when you are looking at other fences in your neighborhood or when you are looking in home magazines. You should also contact your city or residential association to make sure that there is no regulation for fence construction.

Layout of your fence

Marking Property Line

Tie down your string at this place, and it would be perpendicular to the house. Mark the position of your first spot, then measure out for the line to mark the rest of the posts. Thee string should be at the outside of this post, so you have to measure in from the string for center of the posts. Mark this with a stake so you can see them. If your fence goes down hills you have two choices, you can have top of the fence to follow the slope of the hill or you can keep the fence sections level and step the fence down at each post. If you like to have step down fence, estimate the height different from top and bottom of the hill and divide this number by number of sections. And you will get the amount to step the fence down at each post.

Digging Fence Holes

You can use a clamshell digger to dig your postholes but this is a very hard fork and if you got plenty holes or you have hard ground it could rent a power auger but you normally have to be two people to run it. In most areas you need to have the postholes below the frost line to make sure that the post will stay in place when the ground starts to heaves due to the frost. How to plan a deck diy with 3D deck photos and decking plans, designs, and diy ideas. you design deck plans for diy how to build a deck plan and free decking design pictures. As a guideline you should bury about half of the corner posts and about a third of the line post underground.

Setting Fence Posts

It’s a good idea to put a 30-40cm layer of gravel at the bottom of each hole to prevent rot and decay. The gravel will allow water tat collects at the bottom of the hole to drain away. Set the end post first and line up the post edge along your layout string. To prevent water from running down between the post and the concrete you should fill the hole little bit higher than the ground and slope the top of the concrete away from the pole a little. Brace the post in place while the concrete cures. The line post doesn’t need that much support. Normally it’s enough to set them with dirt. Use a spacer to get a consistent distance between them and shovel dirt around them when you have the posts in position. When you have 15 cm filled with dirt pack the dirt down and keeps filling it up. When you have all posts set hard, trim of the tops to get proper height.

Installing Fence Panels

Stringers are the pieces that you have horizontally between the posts and are for supporting your panel board how many you needs and where to place them depends on the design of your panel. But you should at least have 5 cm below the bottom stringer to avoid rot and to make it easier to move. To attach the stringers you should cut them to fit between the posts and nail them to the posts. Always remember to use galvanized nails. What design of the panel you like to have is up to you but it looks best if you keep the entire panel consistent and symmetrical.

Arthor and Source: Daniel Roshard

How to Bulid a Wood Fence

Fences can be made of aluminum, vinyl, iron, and wood. Likewise, all of these materials are made to mark territories and provide homeowners with privacy. Each of these raw materials has a different cost. Depending on the manufacturers, fences are ready-made and can be installed. However this may cost more than buying raw materials. Among these materials, wood is known as the most basic and popular choice of homeowners.

Prepare the tools and materials

Here is a checklist of the tools and materials you will need: Boards and posts, Gravel and sand, Hammer, Hand saw, Level, Marking pencil, Nails, Paint , Post-hole digger, Power saw, Ready mixed concrete, Hatchet or small axe, Steel tape, Tamping rod, Wood chisel, Wood preservative

Step by Step How to Build Wood Fencing

Finding your Property Line

So you've decided that you need a fence, and even know what type of fence to want to build. Now you must consider the other issues involved, such as knowing where your property lines are, what building restrictions are in place, as well as the feelings of your neighbor. You need to take all of these things into account before you put nail to post, or you could have a costly disaster on your hands.

Something that you need to do before you start building is to have an updated land survey on hand. Already existing fences may or may not lie right along the property line, so don't use them as a guide. Be sure of where your property ends and your neighbor's begins.

Important Legal Factors before Building a Fence